Lynxmotion Tech Support

www.lynxmotion.com
It is currently Sat May 25, 2013 10:14 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 58 posts ]  Go to page Previous  1, 2, 3, 4
Author Message
PostPosted: Tue Jul 12, 2011 3:09 pm 
Offline
Roboteer

Joined: Tue Mar 01, 2011 11:17 am
Posts: 21
And another


Attachments:
IMG_0178.jpg
IMG_0178.jpg [ 736.45 KiB | Viewed 1140 times ]


Last edited by Fish (Admin) on Tue Jul 12, 2011 3:57 pm, edited 1 time in total.
Image was added twice.
Top
 Profile  
 
PostPosted: Tue Jul 12, 2011 4:02 pm 
Offline
Roboteer

Joined: Tue Mar 01, 2011 11:17 am
Posts: 21
Jim said:
The image helped a lot. It looks like the power to the receiver is wrong. Ground is on the far right, power next to it, and signal is on the far left. It looks like you have the red power wire going to the signal pin. Looks like you solved the motor controller going to the wrong channels.


This HiTech controller is labelled opposite the one on Schematic 4-2. I have wired it in the other configuration with no better results.


What are the laser cut panels?

What about the position of the 6 nano switches?


Attachments:
IMG_0179.jpg
IMG_0179.jpg [ 640.68 KiB | Viewed 1134 times ]
Top
 Profile  
 
PostPosted: Tue Jul 12, 2011 4:32 pm 
Offline
Roboteer

Joined: Tue Mar 01, 2011 11:17 am
Posts: 21
I got out a macro lens to better illustrate the parts.

I am getting a little anxious. Monday I leave for a 2 month filming assignment on a remote location of Kodiak Island. I will be filming a Kodiak bear family and had hoped to mount a GoPro on this robot for some unique footage.

Here is the link to last years adventure.
http://www.youtube.com/watch?v=lD63JOjqTDg

All help and suggestions are greatly appreciated.

Thanks
Kent


Attachments:
IMG_7185.jpg
IMG_7185.jpg [ 625.55 KiB | Viewed 1130 times ]
Top
 Profile  
 
PostPosted: Tue Jul 12, 2011 4:34 pm 
Offline
Lynxmotion Founder
User avatar

Joined: Mon Oct 31, 2005 10:46 am
Posts: 9325
Location: my quiet place
kentsj wrote:
This HiTech controller is labelled opposite the one on Schematic 4-2. I have wired it in the other configuration with no better results.


I see what you are saying, but please leave it where the motor controller connectors are in channels 1 and 2 and you still haven't fixed the issue with the power. In the image above the row closest to you is ground, the next row is power, and the last row is signal. You have the ground right, but you have changed the connector so the red power wire is not going to the power row. You have it going to the signal wire. The receiver is not getting any power.

kentsj wrote:
What are the laser cut panels?


The plastic panels that go on the top and bottom of the rover. They have a masking on them that when removed reveals a very clean shiny surface.

kentsj wrote:
What about the position of the 6 nano switches?


They are perfect for the tutorial as it is in figure 4-2.

_________________
Jim Frye, the Robot Guy
http://www.lynxmotion.com
I've always tried to do my best...


Top
 Profile  
 
PostPosted: Tue Jul 12, 2011 5:28 pm 
Offline
Roboteer

Joined: Tue Mar 01, 2011 11:17 am
Posts: 21
I put the red wire to the middle row. No idea how it got moved but it still acts erratically and I have minimal control. For your information it acted normally for a short period of time and than back to uncontrollable.


Top
 Profile  
 
PostPosted: Wed Jul 13, 2011 9:08 am 
Offline
Lynxmotion Founder
User avatar

Joined: Mon Oct 31, 2005 10:46 am
Posts: 9325
Location: my quiet place
1. Are you extending the antenna on the transmitter? Please do so if you are not.
2. Untangle the antenna on the receiver and put it through some sort of plastic tubing to extend it.

If the thing acted right for even a short time, then start fiddling with the wires to see if you can find a bad connection somewhere. With power restored to the receiver maybe we can make some progress. ;)

_________________
Jim Frye, the Robot Guy
http://www.lynxmotion.com
I've always tried to do my best...


Top
 Profile  
 
PostPosted: Wed Jul 13, 2011 9:37 am 
Offline
Roboteer

Joined: Tue Mar 01, 2011 11:17 am
Posts: 21
Good Morning Jim;
1. I had extended the antenna before. Then it did not make a difference.
2. I fiddled with the wires and behold it now works!! But, All controls are reverse of what they should be and reverse is much slower than forward. Maybe that is normal.
Progress is good.
Kent


Top
 Profile  
 
PostPosted: Wed Jul 13, 2011 9:46 am 
Offline
Lynxmotion Founder
User avatar

Joined: Mon Oct 31, 2005 10:46 am
Posts: 9325
Location: my quiet place
Ok you definitely need to track that wiring issue down so it doesn't come back to bite you later. ;)

The speed should be the same in forward and reverse. Now that the main problem is established you should be able to go back to the tutorial to sort out the reversed controls. It could be the motors are wired in reverse, or the radio needs some channels to be reversed. But you should be able to get it going from the tutorial. If not then tell me in what step of the tutorial it does not do what the text says it should.

_________________
Jim Frye, the Robot Guy
http://www.lynxmotion.com
I've always tried to do my best...


Top
 Profile  
 
PostPosted: Wed Jul 13, 2011 9:52 am 
Offline
Lynxmotion Founder
User avatar

Joined: Mon Oct 31, 2005 10:46 am
Posts: 9325
Location: my quiet place
One thing... If you flip switch 5 on the Sabertooth off it will disable the autocalibrate. Then you adjust the sliders on the sides of the joysticks till the robot does not creep in any direction. Than you should have full speed in forward and reverse.

_________________
Jim Frye, the Robot Guy
http://www.lynxmotion.com
I've always tried to do my best...


Top
 Profile  
 
PostPosted: Wed Jul 13, 2011 10:35 am 
Offline
Roboteer

Joined: Tue Mar 01, 2011 11:17 am
Posts: 21
On the Sabertooth there is a red Error light that randomly blinks when the unit is under power. If I turn the unit on operate for 30-90 seconds that error light blinks and eventually the Forward Reverse slow to a slow crawl. If I then turn the unit off and back on it will run normally for another 30-90 second cycle.


Top
 Profile  
 
PostPosted: Wed Jul 13, 2011 12:27 pm 
Offline
Lynxmotion Founder
User avatar

Joined: Mon Oct 31, 2005 10:46 am
Posts: 9325
Location: my quiet place
Is it getting hot? The Sabertooth may have been damaged in your earlier wiring changes. Sounds like it's the culprit.

_________________
Jim Frye, the Robot Guy
http://www.lynxmotion.com
I've always tried to do my best...


Top
 Profile  
 
PostPosted: Fri Oct 12, 2012 5:26 am 
Offline
Roboteer

Joined: Tue Oct 09, 2012 9:09 am
Posts: 2
The folks who did the original BeetleCam are not selling anymore perhaps until the end of 2013.
So I am interested in building something similar myself.

However I want to build a 6 WD version, which is their latest version.

Same as the example I want to have tilt for the camera, be good if pan used to rotate the vehicle.

Need good range say 100 metres or approx 300 feet.

Does not need to go fast.

Looking at the options for tilt of the camera I am not sure what I need but needs to support Canon DSLR and 35mm lens.
Option of adding Zoom control later would be good.
I have separate remote camera for focus and trigger.

I will look at placing a protective shell on top of the whole rig.

I don't understand the specs of the Hitec RC, I read
HiTec Aggressor 2-Ch AM 75MHz with Rx and servo
or
HiTec Aggressor CRX 75MHz 3 FM w/ DCS Rx and Servo

Which one is best or are there better choices now?


Top
 Profile  
 
PostPosted: Tue Oct 23, 2012 7:52 am 
Offline
Site Admin
User avatar

Joined: Fri Aug 31, 2012 7:45 am
Posts: 529
The Thumper would make a good 6WD platform:
http://www.robotshop.com/dagu-wild-thum ... sis-2.html
If you only need a tilt mechanism for a camera, consider the SPT400 series which can be found here:
http://www.robotshop.com/pan-tilt-servo-gearboxes.html
Note that they are supposed to be used with a standard sized Hitec servo.
We don't offer (nor are aware of) any systems which can automatically adjust zoom, so you may need to develop your own.
As for the R/C system itself, the choice is yours. You'll need two channels for the base, one for the tilt, and one for the zoom.
It may be good to have a spare channel or two for later.
http://www.robotshop.com/rc-communications.html

_________________
Coleman Benson
Lynxmotion
Imagine it. Build it. Control it.™
http://www.Lynxmotion.com


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 58 posts ]  Go to page Previous  1, 2, 3, 4

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group